USD
EUR
HKD
- Description
Scratch removal kit:
Dry using.
1000-1500RPM required.
From coarse to fine grinding step by step.
Z shape reciprocating grinding and polishing route.
Gentle touch onto glass with steady and stable strength.
Grind to have glass powder.
1/2 or 2/3 of each Z shape overlaps when reciprocating.
Grinding regularly in same direction.
Do not stay in a point!
1/2 bigger processing area than the one of previous process.
Finer grinding, bigger disc, softer strength.
Kit list:
2" 1# Blue grinding disc(Coarse Grinding): 30 Pcs
2" 2# Red grinding disc(Medium Grinding): 30 Pcs
2" 3# Green grinding disc(Fine Grinding): 30 Pcs
2" Wool pad: 02 Pcs
2" Sponge pad: 02 Pcs
2" Velour base: 02 Pcs
3" 1# Blue grinding disc(Coarse Grinding): 30 Pcs
3" 2# Red grinding disc(Medium Grinding): 30 Pcs
3" 3# Green grinding disc(Fine Grinding): 30 Pcs
3" Wool pad: 02 Pcs
3" Sponge pad: 02 Pcs
3" Velour base: 02 Pcs
5" Sponge pad: 01 Pcs
5" Velour base: 01 Pcs
Polishing cream: 04 Bottles
Adjustable speed grinder 01 pcs
Cleaning PU blad 01 Pcs
Water Supply:
Dry use in the process of grinding.
Spray water on the polishing area intermittently
Clearance:
Do clearance after every grinding process which shall leave abrasives grain that would cause new scratch in next process.
Scratch size and solution:
1). Tiny: See from special angle. Polishing directly.
2). Small: See directly but can't feel by finger nail and pad. Polishing directly, or, 3# disc grinding and then polishing.
3). Medium: Feel by finger nail but pad. 2# and then 3# grinding and polishing, or, 3# disc grinding and then polishing.
4). Deep: Feel by both finger nail and pad. 1#, 2#, 3# grinding and polishing.
Note:
1. Practise to know the difference of every process before doing formal job.
2. A certain surface deformation would be cause by processing the deep/medium scratch or improper handling to small scratch,which would especially affect the driver's line of sight if doing with windshield of vehicle.
3. Take good care of and check very often about temperature caused by continual friction that would break glass (Tempered glass is relatively safe).Once feeling hot and burning the hand,stop for a while.
4. If necessary,it's allowed to process with water. However, Water will affect the grinding performance of 2# and 3# disc. No suggest to use 1# disc that makes roughest grinding mark which is not easy to remove by the 2# and 3# disc with water. Begin with 2# disc if watering!
Dry using.
1000-1500RPM required.
From coarse to fine grinding step by step.
Z shape reciprocating grinding and polishing route.
Gentle touch onto glass with steady and stable strength.
Grind to have glass powder.
1/2 or 2/3 of each Z shape overlaps when reciprocating.
Grinding regularly in same direction.
Do not stay in a point!
1/2 bigger processing area than the one of previous process.
Finer grinding, bigger disc, softer strength.
Kit list:
2" 1# Blue grinding disc(Coarse Grinding): 30 Pcs
2" 2# Red grinding disc(Medium Grinding): 30 Pcs
2" 3# Green grinding disc(Fine Grinding): 30 Pcs
2" Wool pad: 02 Pcs
2" Sponge pad: 02 Pcs
2" Velour base: 02 Pcs
3" 1# Blue grinding disc(Coarse Grinding): 30 Pcs
3" 2# Red grinding disc(Medium Grinding): 30 Pcs
3" 3# Green grinding disc(Fine Grinding): 30 Pcs
3" Wool pad: 02 Pcs
3" Sponge pad: 02 Pcs
3" Velour base: 02 Pcs
5" Sponge pad: 01 Pcs
5" Velour base: 01 Pcs
Polishing cream: 04 Bottles
Adjustable speed grinder 01 pcs
Cleaning PU blad 01 Pcs
Water Supply:
Dry use in the process of grinding.
Spray water on the polishing area intermittently
Clearance:
Do clearance after every grinding process which shall leave abrasives grain that would cause new scratch in next process.
Scratch size and solution:
1). Tiny: See from special angle. Polishing directly.
2). Small: See directly but can't feel by finger nail and pad. Polishing directly, or, 3# disc grinding and then polishing.
3). Medium: Feel by finger nail but pad. 2# and then 3# grinding and polishing, or, 3# disc grinding and then polishing.
4). Deep: Feel by both finger nail and pad. 1#, 2#, 3# grinding and polishing.
Note:
1. Practise to know the difference of every process before doing formal job.
2. A certain surface deformation would be cause by processing the deep/medium scratch or improper handling to small scratch,which would especially affect the driver's line of sight if doing with windshield of vehicle.
3. Take good care of and check very often about temperature caused by continual friction that would break glass (Tempered glass is relatively safe).Once feeling hot and burning the hand,stop for a while.
4. If necessary,it's allowed to process with water. However, Water will affect the grinding performance of 2# and 3# disc. No suggest to use 1# disc that makes roughest grinding mark which is not easy to remove by the 2# and 3# disc with water. Begin with 2# disc if watering!
You May Like
-
$45.06
-
$8.83
-
$1.17
-
$17.51
-
$54.94
-
$0.36
-
$30.00
-
$0.97
-
$0.88
